Tech Support Knowledgebase Browse
 
Tools
Rss Categories

 Featured
iGO [Street mode] - Updating your Camps POIs to latest version

Author: Robert Taylor Reference Number: AA-00480 Views: 11894 Created: 2015-02-12 09:44 Last Updated: 2017-10-18 15:51 94 Rating/ 4 Voters

HN5i HN6 HN7 Hema Navigator HN5i, HN6 and HN7 ONLY!

The information contained in this article applies ONLY to the Hema Navigator HN5i, HN6 and HN7 models.
It does not pertain to other Navigator models.

IMPORTANT!

The update process shown here will replace the existing Camps POI content on your Navigator with the latest Camps POIs at the time you perform the update.
Be sure that you actually want the latest Camps POIs before doing the update!

ie.If you currently own the Camps 6 or 7 book, it will not be compatible with the new Camps 8 POI content. Only the Camps Australia Wide 8 book is compatible with the Camps 8 POIs.

Camps 6 Camps 7 Camps 8

Following the release of a new version of the Camps Australia Wide book, the Camps POI set for the Hema Navigator HN5i, HN6 and HN7 are released. 

There is usually a delay of a month or two between the book's release, and the availability of the data allowing updates of your Navigator.

This document shows you how to find and install the new content onto your Navigator.


Prior to installing the update for Camps POI content, start iGO on your Navigator (Street Mode).

Tap on the Find Places button, and you should then see the icons showing the current version of Camps POI content (as shown in the example below).

Before Update


These instructions assume that you are familiar with the process of using the NaviExtras Toolbox software to perform updates on your Navigator.

If you are not familiar with the process, please read and understand the instructions here:

HN5i - Updating iGO content

HN6 - Updating iGO content

HN7 - Updating iGO content


As per the instructions for updating your Navigator using NaviExtras Toolbox, connect your Navigator in MASS STORAGE MODE, and start the NaviExtras Toolbox software.

NOTE!

We highly recommended performing a backup prior to performing any updates.

Once the NaviExtras Toolbox software is running, and your Navigator is connected and recognised, DO A BACKUP, and then follow the process below to install the latest Camps content on your Navigator.


Click the Maps button on the toolbar at the left side of the NaviExtras Toolbox window.

NOTE!

You will NOT be able to click on the Maps button in Naviextras Toolbox until you have your Navigator connected.ie. the button will be inactive.

Click on Australia & New Zealand under Maps & More

Then, click on POIs once you have selected Australia & New Zealand

Either click the READ MORE button, or the PIN Icon

Naviextras Toolbox


NaviExtras Toolbox will display some more detailed information about the Camps POI update.

Click the GET FOR FREE button to add the content to the current list of updates.

Naviextras Toolbox


NOTE!

If you have already downloaded and installed the Camps POI update, you will see a warning to that effect as shown below.

Naviextras Toolbox


NaviExtras Toolbox will display a prompt showing that you have new content available for installation.

Note that the updates which are available for installation will vary depending upon when the Navigator was last updated.

For example, if you already had two updates pending, then you can add the Camps POI update to the pending updates. In this case you would see 3 new packages to install on this screen.

Click the Install button to start the process.

Naviextras Toolbox

NOTE!

You will most likely to be prompted to perform a backup prior to installing the update(s).

WARNING!

The Camps update for HN7 model Navigators will take longer, as there is more data contained within the update. 


NaviExtras Toolbox will then start downloading the new content, displaying a status window as the process proceeds.

Naviextras Toolbox - Installing Update


After the download and installation of the new content is complete, NaviExtras Toolbox displays a message indicating success or otherwise, as shown below. Clikc the OK button to exit this window.

Naviextras Toolbox - Update Complete


After you have installed the Camps POI content, start iGO on your Navigator (Street Mode).

Tap on the Find Places button, and you should then see the icons showing that you are now running the latest Camps POI content.

Congratulations! The process is complete - fire up the billy, and put your feet up on the camp chair ;-)

After Update


Please rate articles! It helps us to ensure that you can find relevant information in the Knowledgebase.
You can use the Please rate this article option from the Tools menu at upper-right.
Comments left when rating articles are not replied to, although they are viewed and taken into account.
If you have an issue you need help with, please submit a ticket at Hema Tech Support

Content found in the Knowledgebase is accurate as at time of publication.
Copyright © 2015 Hema Maps Pty Ltd